Chrome Flush Hinge
Hinge Pins and Nipple
Cab Lock Handles
Door Holders
Weld-on Stake Pocket
D-Rings and Lashing Rings
|
Coupler Locks
Hitch Pins and Hairpin Clips
Locking Receiver Hitch Pin
Safety Chains and Hooks
Linch Pins
Tie Down Straps |
| Chrome Flush Hinge |
|
Commonly known as a "refrigerator Door Hinge". Mounts with six No. 10 flat or oval head screws (not included). Can be mounted as a left hand or right hand hinge. |
 |
| Part No. |
Width |
Length |
| 104 |
3 1/4" |
6" |
|
| |
|
| Hinge Pins and Nipple |
|
| Used for custom building your own light duty ramp door. Hinge Pin Nipples are welded to outer frame and to door, aligning them so the Hinge Pin may be inserted. Greaseable hinge pins have a grease zerk installed on one end and an outlet hole to allow lubrication of the hinge. |
 |
| Part No. |
Description |
Diameter |
Length |
| HP12-412G |
Hinge Pin, 2 piece, Greaseable |
1/2" O.D x 3/4" Base |
4 1/2" |
|
| |
|
215-244 Hinge Pin: Ideal for use when building a Cargo Ramp Door or when replacing Cargo Rear Ramp Door Hinges.
215-241 Hinge Pin: Ideal for use when building a Utility Trailer Mesh Ramp or for replacing Mesh Ramp Hinges.
|
 |
| Part No. |
Description |
Diameter |
Length |
| 215-244 |
Hinge Pin weld on , 2 piece, Greaseable |
3/4 inch |
10 inches |
| 215-241 |
Hinge Pin weld on , 2 piece, Greaseable |
5/8 inch |
8 inches |
|
| |
|
| Cab Lock Handles |
|
| We keep the locking models in-stock, however you can special order the non-locking models as well. The door/compartment handles are designed for use with cab locks. All shafts are 5/16" square |
 |
| Part No. |
Description |
Shaft Length |
| 276 |
"L" handle with lock |
2 1/2" |
| 277 |
"L" handle without lock |
2 1/2" |
|
| |
|
| Door Holders |
|
| One part is mounted to the door, the other to the side of the trailer. Primarily used for holding trailer doors open, but can also be used on trailer windows. All metal parts are zinc plated. |
 |
| Part No. |
Description |
| 5601 |
Hook and Keeper |
|
| |
|
| Weld-on Stake Pocket |
|
| Designed for use on flat bed trucks or trailers. Accepts std 2"x4" stakes. Sold unpainted. |
 |
| Part No. |
Gauge |
Height |
I.D. |
| STKP34 |
4 |
3" |
1 5/8" x 3 1/2" |
|
| |
|
| D-Rings and Lashing Rings |
|
| A full range of sizes of D-rings and Lashing rings is available; light duty for rope ties in cargo and horse/stock trailers or heavy duty for chains, etc. on equipment/flat bad trailers. |
 |
| Part No. |
Description |
Capacity |
| D14-20 |
Recessed zinc-plated w/overall measurements of 5" long, 3 1/2" wide and 3/8" deep |
1,200lb Rated |
| DR14-30 |
D-Ring surface mount 4 1/5" OD w/plastic trim zinc plated |
|
| RDR801 |
4 1/2" x 4 7/8" O.D. Recessed bracket, w/ 1 3/8" I.D. forged ring |
6,000lb Rated |
|
| |
|
| Coupler Locks |
|
| Precision made of aircraft aluminum, EZ lock brackets from Blaylock Industries will not rust and are highly visible to discourage would-be thieves. Easy to install. Simply place bracket over the coupler, insert the pin and attach padlock. |
 |
 |
 |
 |
 |
 |
| Part No. |
Description |
Ball |
| EZTL33-40D |
EZ-Lock Universal Coupler Lock. Fits more than 30 different sizes and models of trailer couplers. 3/4" steel locking pin. Comes with padlock. |
1 7/8", 2",
& 2 5/16" |
| EZHB2 |
Fits Hammerblow Bulldog Coupler. Does not come with padlock. |
2" & 2 5/16" |
| EZHB2-40D |
EZHB2 and one padlock. |
2" & 2 5/16" |
| EZTL50-40D |
Fits most gooseneck couplers. Comes with padlock. |
2 5/16" & 3" |
|
| |
|
| Hitch Pins & Hairpin Clips |
|
 |
| Part No. |
Description |
| HP583 |
Receiver Hitch Pin, 5/8" Dia x 3" L, w/keeper pin |
| 43702 |
Receiver Hitch Pin, 5/8" Dia x 2 1/4" L, without keeper pin |
| 12H |
Hitch Pin, 1/2" Dia x 3 1/2" L, w/keeper pin |
| 43703 |
Hairpin Clip (Keeper pin) Class ll |
| 43704 |
Hairpin Clip (Keeper pin) Class lll |
| 66308 |
Hairpin Clip 1/4" x 4" (used for stand-up ramp) |
|
| |
|
| Locking Receiver Hitch Pins |
|
 |
|
| Part No. |
Description |
| DB-3 |
Locking receiver hitch pin, 5/8" x 3" |
| 18-2058 |
Locking receiver hitch pin, 5/8" x 3" |
|
| |
|
| Safety Chains and Hooks |
|
SAE Code J684, Section 6.3.1 reads: "Two lengths of safety chain or equivalent shall be used. They shall be connected from the opposite sides of the trailer tongue to the towing vehicle and when passing forward to the towing vehicle, shall be crossed under the trailer tongue in such a manner that they will cradle the trailer coupling and tongue in the event of separation of the coupling or ball."
For Proper compliance, we recommend the use of two safety chains or two safety cables attached at two separate points to the trailer. |
| Safety chains provide additional assurance by securing the trailer to the tow vehicle. |
 |
| Part No. |
Description |
Diameter |
Overall Length |
Class |
Min. Breaking Strength |
| SC1448 |
7/16" Hooks both ends |
1/4" |
48" |
III |
5,000lb |
|
| Our S-Hooks are made of high test steel alloy and bright zinc plated to assure dependability and strength |
 |
| Part No. |
Hook Diameter |
Chain Size |
Class |
Min. Breaking Strength |
| 4480 |
7/16" |
1/4" |
ll & lll |
5,000lb |
|
| The heat treated, electro-zinc plated clevis slip hooks meet all requirements for Grade 43 High Test Chain. This versatile design finds many uses in industry or on the farm. DO NOT use these hooks for overhead lifting and do not exceed the working load limit. |
 |
| Part No. |
Size |
Working Load Limit |
Min. Breaking Strength |
| 385CHOOK |
For 3/8" chain |
5,400lb |
16,200lb |
|
| |
|
| Linch Pins |
|
| Manufactured from low carbon steel, the pin portion of the linchpin has a rockwell hardness RA 50-60 with a 60kg load. The ring portion of the linchpin is hot drawn spring steel. Zinc plated for corrosion resistance. |
 |
| Part No. |
Pin Diameter |
| LP316 |
3/16" |
| LP14 |
1/4" |
| LP38 |
3/8" |
|
| |
|
| Tie Down Straps |
|
|
| Part No. |
Description |
Safe Working Capacity |
| 1012 |
1" x 6' cam buckle tie down |
600lb (272Kg) |
| 1006 |
1 1/6" x 15' ratchet tie down |
800lb (303Kg) |
| 1501 |
1.5" x 15' heavy duty ratchet tie down |
1300lb (590Kg) |
| 1502 |
1.5" x 15' heavy duty ratchet tie down |
2200lb (1000Kg) |
| 2012 |
1 3/4" x 25' emergency tow strap |
2666lb (1212Kg) |
| 2002 |
2" x 27' heavy duty ratchet tie down |
3300lb (1500Kg) |
| 2001 |
2" x 30' heavy duty ratchet tie down |
3300lb (1500Kg) |
| 4821XW-30F |
4" x 30' winch strap |
5400lb (2449Kg) |
|