Axle Beams
Axle Spring Seats
Brake Mounting Flanges
Brake Mounting Bolts
Brake Mounting Nuts and Lockwashers
Replacement Spindle Washers
Replacement Spindle Nuts
Spindles
Hubs (Idler)
Hub and Drum Assemblies

Please contact our office to order/inquire about axle beams. We will need the answers to the following questions:
Please Download and fax the following request for quote and instructions on
- measuring spring & torsion axles - click here

1. Spindles: Are they straight, drop or E-Z lube?
2. Inner and Outer Bearings: What are the bearing numbers?
3. Seal: What is the I.D. and O.D. or Reference# of the seal?
4. Tube: What is the outside diameter? Is the tube solid bar or tubular?
5. Hub Face: What is the measurement from center to center of spindles?
6. Spring Pads: What is the measurement from center to center of pads?
7. Brake Flange: What is the measurement from outside to outside of brake flanges?

Equation to figure hub face from flange to flange dimensions:
 

Please contact our office to order/inquire about spindles not shown here. Spindles come complete with spindle nut, washer and cotter key (tang washer supplied with grease lubed spindles).

How to Order Replacement Hubs or Hub and Drums

1. Determine the bolt pattern of the hub. Acrobat Reader Required, download now.
2. Determine the inner and outer bearing numbers. Note whether the bearings use grease or oil bath lubrication.
3. Measure the old hub seal to insure that the I.D. and O.D. dimensions will be the same.
4. Verify the stud diameter.
5. If the axle is a brake axle, measure the diameter and width of the brake to determine brake size.
6. Look for any casting numbers on the front or rear of hub or hub and drum.
7. On heavier axles, such as the dexter 8,000lb or 9,000lb axles, you need to determine the hub pilot diameter. This can be accomplished by measuring the center hole of your wheel.
8. On 8,000lb and larger axles determine if it is equipped with ABS, and requires a drum/rotor with ABS exciter ring installed.

Fits BT8 1" Spindle, L44643 inner/outer bearings
Capacity of 1,250lb per each

Fits Dexter 2,000 lb axle, BTR 1 1/16" Spindle, L44649 inner/outer bearings
Available in Standard or E-Z Lube applications (Complete E-Z lube not shown)

Fits BT8 1" Spindle, L44643 inner/outer bearings
Capacity of 1,250lb per each
5 1/2" diameter hub flange, use with 8" - 10" wheels
6 1/2" dia. hub flange, use with 12" - 15" wheels (not shown)

Fits Dexter 2,000 lb axle, BTR 1 1/16" Spindle, L44649 inner/outer bearings
Available in Standard or E-Z Lube (EZ lube not shown, contact us to order).
5 1/2" dia. hub flange, use with 8" - 10" rims
6 1/2" dia. hub flange, use with 12" - 15" rims (not shown)

L68149 Inner/ L44649 Outer Bearings
Capacity of 1,750lb per each
Fits #84 Spindle
Std. Grease or E-Z Lube Application
(4.75" & 5.5" Bolt Circles & EZ-Lube not shown. Contact us to order.)
Used on Dexter and most 3,500lb Axles
4 Different Bolt patterns

25580 Inner/15123 Outer Bearings
Capacity of 3,000lb per each
Fits Dexter 5,200lb / 6,000lb axles
For spindles with 2 1/8", or 2 1/4" I.D. Grease Seal
Std. Grease or E-Z Lube Application

25580 Inner/14125 Outer Bearings
Capacity of 3,500lb per each
Fits Dexter 5,200lb thru 7,000lb axles

How to Order Replacement Hubs or Hub and Drums

1. Determine the bolt pattern of the hub. Acrobat Reader Required, download now.
2. Determine the inner and outer bearing numbers. Note whether the bearings use grease or oil bath lubrication.
3. Measure the old hub seal to insure that the I.D. and O.D. dimensions will be the same.
4. Verify the stud diameter.
5. If the axle is a brake axle, measure the diameter and width of the brake to determine brake size.
6. Look for any casting numbers on the front or rear of hub or hub and drum.
7. On heavier axles, such as the dexter 8,000lb or 9,000lb axles, you need to determine the hub pilot diameter. This can be accomplished by measuring the center hole of your wheel.
8. On 8,000lb and larger axles determine if it is equipped with ABS, and requires a drum/rotor with ABS exciter ring installed.

Fits #84 Spindle, L68149 Inner/L44649 Outer Bearings
Capacity of 1,750lb per each
Available in Standard or E-Z Lube Application
Used on Dexter and most 3,500lb axles
Drum size: 10" x 2 1/4"

Fits #84 Spindle, L68149 Inner/L44649 Outer Bearings
Capacity of 1,750lb per each
Available in Standard or E-Z Lube Application
Used on Dexter and most 3,500lb axles
Drum size: 10" x 2 1/4"

Fits Dexter 5,200lb and 6,000lb axles,
#42 Spindle, 25580 Inner / 15123 Outer Bearings
Capacity of 3,000lb per each
For Spindles with a 2 1/8" or 2 1/4" I.D. Grease Seal
Used on Dexter and most 3,500lb axles
Drum size: 12" x 2"

Fits Dexter 5,200lb thru 7,000lb axles, #42 Spindle, 25580 Inner / 14125 Outer Bearings
Capacity of 3,500lb per each
For Spindles with a 2 1/8" or 2 1/4" I.D. Grease Seal
Available in Std Grease or E-Z Lube applications
Drum size: 12" x 2"

Hayes/Alko: Fits #99 Spindle, 28580 Inner/25580 Outer Bearings
For 10K G.D. Hayes Axle
Oil Bath Hub (Dual Wheel)
Drum size: 12 1/4" x 3 1/2"

Oil Bath Hub, 387A Inner / 25580 Outer Bearings
Fits Dexter 9K (after 10/89) and 10K G.D.
Capacity of 5,000lb per each
Drum size: 12 1/4 " x 3 3/8 "
Available with ABS exciter ring installed

8 Bolt, 6.5" Bolt Circle

Quality - 10K lb. Hub & Drum
12 1/4" x 3 1/2".

Notes:
1. Swivel Flange Lug Nuts to be torqued to 130-170 FT. LBS.
2. Spindle nuts torqued to 100 FT. LBS. then backed off 1/4 turn.
3. U-Bolts nuts to be torqued to 130-170 FT. LBS.
4. Brake attaching bolts to be torqued to 70-100 FT. LBS.
5. Oil / Grease cap to be torqued to 20-30 FT. LBS.

Each wheel bearing kit includes:
- One Inner Bearing and Race
- One Outer Bearing and Race
- Grease Seal
- Cotter Pin

Dimensions are as follows:
A=Thread Diameter, B=Stud Length, C=Spline Length, D=Base Length, E=Spline Diameter